Showing results: 1126 - 1140 of 2497 items found.
-
D1 International
Built-in Bezel at no additional charge3, 3 1/2 or 4 1/2 Digit ReadoutAuto Calibrating, Auto Zeroing, A/D Converter Operation from single +5V supply or 9V battery (low power units)Large easy to read LED or LCD displayOptional Backlighting on LCD ModulesUser Selectable decimal point placement(all models) Built-in color filter on all LED modulesLED colors available, Red (std)Yellow, green, amber, aqua, orange, blue
-
MODEL DPM-3 -
Transducer Techniques, Inc
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
MCH Instruments Co.,Ltd.
Digital Signal Generator*signal frequency:0.1Hz~2MHz, continuously variableave from: square, sine*output attenuator: 0dB,, 20dB, 40dB, 60dB*output level: 20Vp-p in open circuit, not less than 10Vp-p with 50Ω load*rising and falling edge of square not more than 35ns,*sine distortion less than 1%, amplitude –frequency characteristic : ±0.5dB within 100KHz, ±1dB above 1MHz*frequency meter: 10Hz~30MHz*power supply : AC 220V(110V optional)
-
6-Watt Blue Spot Creator -
Advanced Photonic Sciences LLC
*Simple Installation On X-Y-Z CNC Machines*Adjustable Focusing Lens to Create 50, 80, and 100 Micron Diameter Spots*Create High Intensities on Target*Self-Contained Fully Integrated Laser Module Including High Power Blue Diode, Active Cooling, Beam-Forming Optics, and Power Supply*Stable Output Power*Precision Engineering*Rapid Engraving, Etching, and Marking*Modulate Up To 250 kHz*Proportional Control in CW Mode Using 5V CW Signal*High Efficiency*Simple to Power Up and Operate
-
6-Watt Blue Engraving Laser -
Advanced Photonic Sciences LLC
Can be used in laser engraving, marking, and cutting applications. Process wood, plastics, metals, anodized aluminum, stone, tile, and other materials. The adjustable spot can be adapted to the needed distance from laser to the material. The spot, with a size of <100 μm, creates very fine engravings and sharp cutting edges. The built-in driver accepts TTL and analog signals for power adjustments. The laser can be controlled between 0% and 100% of output power. It comes preset and needs only a power supply and a signal source.
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
2100 -
Valon Technology, LLC
1440MHz inputLow noise figure LNA 0.3dB 20 KHigh gain >40dB8-pole ceramic dielectric input filterHigh dynamic range, low-spurious responses Rugged milled aluminum housingRFI shielded constructionDesigned for use with Valon 5009 as LOSuitable for hydrogen line observation and general radio astronomy in the 21cm band.6Vdc @ 400mAIncludes 20” dc power supply cable
-
Analog Devices Inc.
Analog Devices parametric measurement units (PMU) and device power supply (DPS) products provide a flexible range of voltage and current source/measurement capability to meet a wide range of cost-sensitive test application needs. The DPS will source currents to 1.2A and multiple devices can be ganged for even higher power applications.
-
F20AD -
FLC Electronics Inc
This unit contains two independent F20A amplifiers that share common ground reference and power supply.
-
A800D -
FLC Electronics Inc
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
A400D -
FLC Electronics Inc
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
F1020 -
FLC Electronics Inc
This unit contains two independent amplifiers that share common ground reference and power supply. Left channel correspond to the F10A model and right channle corresponds to the F20A model.
-
F10AD -
FLC Electronics Inc
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
A400DI -
FLC Electronics Inc
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
A800DI -
FLC Electronics Inc
This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.